Engineering Training and Seminars
Engineering Training Classes
Engineering and the practical application of science to commerce or industry. Professional practitioners of engineering are called engineers.
Some important terms: Engineering,eng,engineer
From LearningMeasure.com
Introduction to Uncertainty Concepts

UNC101 - Introduction to Uncertainty Concepts.
The purpose of this class is to serve as a introduction to the concept of uncertainty, and a foundation upon which the remaining uncertainty courses at LearningMeasure.com are based.
more...
SI Units - The Ampere
This is the fourth of our introductory courses on the SI units. This course is an introduction to the unit of electric current, the Ampere, and its derived units. The course outline is as follows:
Introduction
The Definition of the Ampere
Realization of the Ampere
Derived Units
Charge (the Coulomb)
Potential (the Volt)
Resistance
more...
Basic Uncertainty Analysis
The second course in a series on uncertainty analysis. Covers basic uncertainty analysis.
more...
MEAS104 - SI Units - The kilogram
The third in a series of seven courses on the SI system of units.
more...
SI Units - The kelvin
This is the fifth in a series of seven courses on the SI system of units, covering the unit of thermodynamic temperature, the kelvin.
more...
Uncertainty Analysis of Complex-Valued Measurands
This is a short course on how to perform uncertainty analysis of complex quantities that are a function of real or complex variables, or real quantities that are a function of complex variables.
more...
SI Units - The Mole
The sixth out of seven courses on the seven SI base units. This course is about the amount of substance, the mole.
more...
SI Units - The Candela
The last in a series of seven courses on the SI system of units. The topic of this course is the SI unit of luminous intensity, the candela.
more...
Fundamental Constants in Metrology
A survey course on the use of fundamental constants in metrology
more...
Applied Math for Calibration Technicians

The purpose of this course is to cover the basic mathematical concepts that are part of the ASQ Certified Calibration Technician exam.
more...
Applied Statistics for Calibration Technicians
This course is the second course of a three part series of courses covering the applied math and statistics body of knowledge for the ASQ Certified Calibration Technician exam, although this course does go a little further into the topic than is covered in the exam. The topic of this course is probability and statistics.
more...
Basic Measurement Concepts
This course introduces basic measurement concepts such as bias, repeatability, systematic error. It covers measurement methods, data characteristics, and the characteristics of measurement systems. This course is a follow-on to MEAS101, which is a prerequisite.
This course is worth 0.1 RU's for the purposes of ASQ CCT recertification.
more...
Inspection, Measurement, and Test Equipment (IM&TE) Specifications
In this course, the basics of IM&TE specifications are covered. In particular what is a specifications, what makes up a specification, the different types of specifications, and how specifications are used in calibration and test.
more...
Quality Control Tools I
This course provides an overview of the seven quality control tools that are called out in the ASQ Certified Calibration Technician body of knowledge. This is the first in an eight course series on the seven basic tools of quality as defined by Kaoru Ishikawa.
more...
QC Tools - Flowcharts and Process Maps
The purpose of this course is to introduce the flowchart, one of Ishikawa's seven basic quality tools. This is one of a series of eight courses on the quality tools. The flowchart is used to document processes graphically. They are used to help identify where to make improvements in a process, or in the design of a new process.
more...
QC Tools - Check Sheets
A check sheet is a tool to collect data associated with the process. It is one of the seven basic quality control tools defined by Ishikawa. The data collected from a check sheet is often used as input into other quality tools. This is one of eight courses on the subject.
more...
QC Tools - Histograms
This is another in a series of eight courses on the seven quality tools defined by Ishikawa. The histogram is a tool that is used to graphically express the distribution of data among various categories. This allows one to graphically express the mean and spread of a set of data, and the number of modes.
more...
QC Tools - Scatter Diagrams
This is another course in a series of eight courses on the seven basic tools of quality as defined by Ishikawa. The scatter diagram is a tool to graphically represent the relationship between two variables. It relies on the human brain's amazing ability to recognize patterns. This diagram can be used to determine correlation between the two variables plotted.
more...
QC Tools - Pareto Diagrams
This is another in a series of eight courses on the seven basic tools of quality as defined by Ishikawa. The Pareto diagram is a tool that can identify what are the most important contributors to whatever is being investigated. The Pareto diagram is a special type of histogram with a cumulative percentage overlaid on it.
more...
From Last Minute Training
Activated Sludge-Treatment Process Design Control and Troubleshooting 2 Days
Operators of wastewater treatment plants aim for trouble-free operation which requires a thorough understanding of the activated sludge treatment process. The course places appropriate stress on the fundamentals of activated sludge, deals with biological process including microbial activity. It covers design criteria and includes a discussion on operation of an activated sludge wastewater
more...
Construction and Building Envelope Inspection
Inspection is observation of construction for conformance with the approved design documents. This course will enable individuals, who are in the inspection and testing field or want to become a special inspector, to understand the nature and the importance of this business.
This course will help you to know and understand the types of inspection and testing involved in a construction project,
more...
Heat Exchangers - Design Operation And Performance
Heat exchangers are important and expensive items of equipment that are used in a wide variety of industries. A better understanding of the basic principles of heat transfer and fluid flow and their application to the design and operation of shell and tube heat exchangers as well as compact and air cooled exchangers that you gain from this course will enable you to improve their effectiveness and
more...
Using Standard Form Contracts for Construction and Design Services
By participating in this practical new course, you will learn how to reduce the occurrence of these problems by using a standardized set of contract documents that have been developed by various industry organizations in Canada including the Canadian Construction Documents Committee (CCDC).
Even when new contract documents are written, considerable effort is necessary to ensure that they are
more...
From Alfa Institute
Advanced Mobile Phone Repair Training Course


Join for our mobile phone repairing course and become a professional mobile phone repair technician.
Training is provided with personal attention at our servise centre. All repairing methods like soldering, desoldering, dismantling and assembling, flashing, formatting, unlocking are covered in the course.
Online Course is also available.
Duration : 2 Months (Fast track course available)
more...
From K2B International
Offshore Drilling Completion


As more oilfields are being exploited, oil and gas operators in Asia are increasingly looking into deepwater development that may offer alternative source of oilfields. Deepwater exploration is generally technically challenging, which calls for the need for new technologies or techniques to optimise oil extraction. With capital investment in drilling and completions accounting for over 50% of
more...
CO2 Enhanced Oil Recovery
Oil fields on the globe are entering a more mature phase of development and it is now timely to consider enhanced oil recovery (EOR) development plans and potential. Injection of CO2 into mature oil reservoirs has been acknowledged as a favorable technique for enhanced oil recovery utilised by the oil industry for decades. Additionally, concerns over greenhouse gas emissions and considerable
more...
Pre-Drilling Risk Management 2008
The depletion of hydrocarbon resources all over the globe is forcing O&G operators to explore in increasingly harsh and unforgiving environments. As a result, the exploration and drilling risks have increased tremendously. Throughout the entire O&G industry, it is common for drilling programmes and plans to fall short of their anticipated reserves and to have drilling success rates immensely
more...
Distillation Units Optimisation
The cornerstone in generating quality gasoline/ fuel is largely dependent on the performance of distillation units. It is however, a challenging task to optimise the performance of distillation units, in particularly the distillation overhead columns as these units are frequently subjected to corrosion due to contaminants in crude oil, salt deposit, poor PH control and inferior distillation column
more...
Intelligent Field Optimization
Among many challenges facing the ONG industry today, how to produce existing reserves more efficiently, how to enhance oil recovery and how to reduce capex and opex definitely rank at the top. ONG professionals are dying to find a solution to get through these bottlenecks towards higher ROI.
To date, the performance of intelligent field has demonstrated an immense value of intelligent
more...
From IndiaEarns.com
PDS Designer (Plant Design Systems)


This course is 4 week series for PDS 3D Designers. Intended for the piping/equipment designer, who will use PDS 3D to create equipment and/or piping models. It focuses primarily on people who will use PDS for Designing or drawing the Equipment/Piping using PDS.
more...
From CAD CAM Services - Jythra Engineering Services
Geometric Dimensioning Tolerancing GDT
We will be starting a in-house training program in the first week of September, 2008.
The couse will be based on ASME Y14. 5M-1994 Standard.
Please send your nominations to training@jythra. com.
Regards,
Krishna Chaitanya
for Jythra Engineering Services
http://jythra. com
more...
From Sigmaview Alliance Training Consultant
Building Maintenance
refer our training program details
or contact: 012-4380442 / 019-2355457
more...
Building Construction - Site Preparation


refer our training program details
or contact: 012-4380442 / 019-2355457
more...
Foundation in Building Tehniques


Course Objectives :
- to explain the foundation in construction site supervision
- to identify and report project failure
- to run specific tests for concrete
- to identify forms for standard in the context of project
supervision
more...
Building Construction - Understanding Contract


refer our training program details
or contact: 012-4380442 / 019-2355457
more...
From Technology Training, Inc.
Dimensional Calibration Procedures


This short course reviews general metrology concepts and then covers calibration equipment and techniques in detail. Specific subjects include mass and weight, weighing devices and mass measurement techniques, precision dimensional instruments such as Vernier and digital calipers, height gages, micrometers and other devices. The course also covers measurement of force, torque, viscosity and
more...
Measurement Uncertainty with an Introduction to Engineering Statistics


...engineering statistics, covering all the usual topics in reliability and statistics and explains how the theory is applied in engineering. Part II introduces statistical concepts associated with measurement uncertainty. The course then covers: error sources and classification, indirect errors, control charts, a step-by-step process of calculating uncertainty, the uncertainty budget and
more...
Thermodynamic Calibration Techniques


Course 133 introduces physical measurement, then covers units of measurement and measuring methods. Error propagation, dimensional equations, traceability and a brief introduction to probability and statistics are presented before proceeding with specific measurement/calibration techniques and specific procedures for temperature, humidity, pressure/vacuum and flow.
more...
Calibration Laboratory Procedures


This short course introduces statistical and management concepts such as Statistical Process Control (SPC) and the Measurement Assurance Process (MAP). ISO standard 17025 and its impact on calibration laboratory management is analyzed clause by clause. ISO 9000 quality programs are also discussed. After a discussion of staffing, documentation, measurement uncertainty and inter-laboratory
more...
Geometric Dimensioning & Tolerancing (GD&T


This short course introduces the concepts of size control and material tolerances. After defining terminology to be used, geometric characteristics and symbols, the course demonstrates how the geometric system works, using practical applications, blue-print reading and interpretation. The course covers application of position tolerance measurement and limits of size methods. Form tolerances for
more...
From ICR Education Society
GATE 2008 Architecture exam + CEED 2008 Exam + NATA 2008 Architecture + aieee 2008 + mhcet 2008


GET IN TOUCH WITH Architecture Aptitude LEADERS
Attention NATA 2008&2009 Aspirant/ GATE 2008 & 2009 Architecture aspirant/CEED 2008 Aspirant/AIEEE 2008 Aspirants/MHCET B.Arch. 2008 Aspirant/SOFT 2008 Aspirant/NIFT 2008 Aspirant/Srishti 2008 Aspirant/WBJEE 2008 Aspirants,
Registration/Enrollment are open for Online MOCKTEST/Correspondence Architecture Tutorial Packages/ study material/sample
more...
From Technology Training, Inc.
Metrology Concepts


This short course covers the measurement process, types and correct use of measurement and test equipment, and measurement standards. It introduces measurement uncertainty and risk analysis. The course includes the procedures necessary to set up and operate a calibration program.
more...
Climatic Test Techniques


An introduction to climatic testing with an overview of field test measurement and analysis. Test methods and conditions of commercial and military test specifications and standards are discussed. Primary emphasis is on understanding the physics of each environment, and available measurement and control techniques.
more...
Digital Data Acquisition


This short course teaches participants to specify, evaluate and use digital data acquisition systems in laboratory and field applications.
more...
Electrical Instrumentation Calibration Procedures


The course briefly reviews of terminology, units, measurement standards, traceability and types of error. The course then covers calibration standards and documents affecting the calibration of electrical items in detail: precision instruments such as VOM devices, oscillators, counters, function generators, power supplies, RF power instrumentation, temperature simulation and measuring equipment,
more...
Understanding ISO 17025


In this short course, ISO standard 17025's impact on test and calibration laboratory operations is analyzed clause by clause. Management requirements are discussed in detail, including organization, the quality system, document Control, contracting issues, handling of complaints, nonconforming work, corrective and preventive action. Technical requirements, including personnel training and job
more...
Instrumentation for Test and Measurement


This short course provides a basic understanding of measurement systems and transducers. Its objective is to give students enough applications information that they can select optimum transducer, amplifier, recording and readout devices to assemble a system for routine measurements of environmental and dynamic phenomena
more...
Instrumentation for Electrical Test and Measurement


This short course provides a basic understanding of electrical measurement systems. It covers meters, 'scopes and transducers, their operating principles, strengths and weaknesses. The course is intended to help students to select optimum meters, transducer, amplifier, recording and readout devices to assemble a system for routine measurements of electrical phenomena.
more...
Applied Measurements


This course provides engineering concepts for the whole measurement system. It covers climatic measuring systems and reviews dynamic theory. Transduers and Wheatstone bridges are discussed, along with signal noise, accuracy and error, before continuing to spectral analysis, sampling, aliasing and filtering. Statistics, uncertainty and the selection of instrumentation systems round out the course.
more...
Telemetry Systems


This short course introduces telemetry systems, carrier signal modulation and telemetry standards. Background is provided in dB, sensors, filtering, signal waveforms and Fourier analysis, to enhance understanding of telemetry modulation techniques. Data Bus standards, bit encoding, special PCM formatting and time codes are discussed. Range Telecommunications, computer systems, and data handling
more...
Fiber Optic Systems


This course provides an excellent foundation in optics and the use of fiber optic cabling in the transmission of data along fiber optic cabling. Applications include telecommunications, automotive, space and military telecommunication systems
more...
Product Noise Control


This course provides an introduction to the physics, principles, language and fundamental techniques used to control noise. Emphasis will be placed on the practical applications of the physical principles behind noise control.
more...
DSP: Digital Signal Processing


This course is an introduction to DSP concepts and implementation. It is applicable to technicians and engineers employed in a wide range of industries.
more...
Environmental Testing Procedures


This short course shows how to conduct meaningful environmental tests. Specific environmental tests such as vibration, shock, climatic, ESS/EST are discussed in detail. Options such as test tailoring and deviation from written requirements of test documentation will be explored.
more...
Environmental Test Specifications


This short course provides understanding and guidance about the contents and proper application of environmental design and test specifications, standards and requirements documents. For newcomers, this course will make environmental design and test less mysterious and formidable. Those with some experience will gain a better understanding, to recognize mistakes and repeat successes.
more...
Digital Signal Processing and Data Analysis


This short course provides participants with a working knowledge of the tools available for analysis of data acquired by digital data acquisition systems for a variety of laboratory and field applications. Basic analysis principals and methods are presented and reinforced with practical examples from everyday testing operations. The interaction between test design, data acquisition and analysis is
more...
Digital Data Acquisition, Signal Processing and Analysis


This short course teaches participants to specify, evaluate and use digital data acquisition systems in laboratory and field applications. It then discusses the tools available for analysis of data acquired by digital data acquisition systems for a variety of laboratory and field applications. Interaction between test design, data acquisition and analysis is emphasized.
more...
Corrosion Prevention Compliance for Defense Acquisition Requirements


This course is designed to lead to a better understanding of US Government initiatives to prevent corrosion in Department of Defense equipment and infrastructure.
more...
Corrosion Control Techniques


This short course provides basic understanding of the mechanisms of corrosion, and measures that can be used to control corrosion. The course also includes a brief overview of the properties of commonly used engineering materials and their resistance to deterioration.
more...
Principles of Project Engineering



...engineering principles, processes and practices. Quality assurance/ control and system engineering techniques and their application to project engineering will be covered.
Because of the highly interactive format, a semester long course can be presented and should be under-stood in this time frame. The instructor welcomes questions and comments during lectures. Pri vate discussions can be
more...
From ICR Education Society
AIEEE 2008/2009 + PACET 2008/2009 + NATA 2008/2009 + KCET 2008 + CET 2008 + TNPCEE 2008 + UPTU 2008 + Architecture sample paper



GET IN TOUCH WITH Architecture Aptitude LEADERS
www.architectureaptitude.com
Attention NATA 2008&2009 Aspirant/ Architecture aspirant/AIEEE 2008 B.Arch. Aspirants/MHCET B.Arch. 2008 Aspirant/WBJEE 2008 B.Arch. Aspirant/Manipal 2008 B.Arch.Aspirants,
Registration/Enrollment are open for Online MOCKTEST/Correspondence Architecture Tutorial Packages/ study material/sample papers & question
more...
From Technology Training, Inc.
Fiber Optics and Optical Calibration
Applications: This course relates to a broad range of fiber optic applications such as telecommunications, automotive, space and military telecommunication systems.
For Whom Intended: This course provides an excellent foundation in optics and the use of fiber optic cabling for division chiefs and QA/ QC personnel as well as technical personnel involved in design, manufacturing and testing and
more...
From in_cr_ove
Value Engineering ( VE / VA)



If you find that decent profits, meeting budget or even survival depend on reducing costs, consider Value Engineering. Value Engineering is a systematic approach involving techniques that reduces costs significantly without affecting performance. VE techniques have helped organizations to reduce design, process and product costs while simultaneously adding value to the customers.
more...
From Abhisam Software
Hazardous Area Instrumentation (Professional)

This e-learning program equips the learner with all the knowledge necessary to select, specify, design and implement Instrumentation and Control Systems in Hazardous Areas. These hazardous areas are those locations that contain explosive and flammable liquids, vapors or gases. Such locations are commonly encountered in Oil & Gas, Petroleum refining, chemicals processing and storage, shipping, tank
more...
Gas Monitors (Professional)

This training program equips you with the knowledge necessary to understand, design, specify, select and implement gas monitors. These gas monitors are used in almost all industries like Oil & Gas, Petrochemical, Chemicals processing, Shipping, Semiconductor fabrication, Power Generation, Steel plants and the like. Gas monitors are used in these industries to detect and warn the presence of
more...
Gas Monitors (Standard)

This training program equips you with the knowledge necessary to understand, design, specify, select and implement gas monitors. These gas monitors are used in almost all industries like Oil & Gas, Petrochemical, Chemicals processing, Shipping, Semiconductor fabrication, Power Generation, Steel plants and the like. Gas monitors are used in these industries to detect and warn the presence of
more...
Hazardous Area Instrumentation (Standard)
This e-learning program equips the learner with all the knowledge necessary to select, specify, design and implement Instrumentation and Control Systems in Hazardous Areas. These hazardous areas are those locations that contain explosive and flammable liquids, vapors or gases. Such locations are commonly encountered in Oil & Gas, Petroleum refining, chemicals processing and storage, shipping, tank
more...
From Tripod Projects And Consultancy Pvt Ltd
PDS-TRAINING-COURSE-CHENNAI-INDIA- TRIPOD PROJECTS IS THE BEST!!
TRIPOD PROJECTS AND CONAULTANCY CHENNAI INDIA is offering WORLD CLASS TRAINING on Plant Design System
ENQUIRE YOUR FRIENDS AND JOIN!!
PDS Modeling
PDS Administration @ Chennai
3-D Modeling
PDS Piping Design @ Chennai
PDS Equipment Modeling @ Chennai
PDS Isogen @ Chennai
PDS Drawing Manager @ Chennai
PDS FRAMEWORKS
PDS EERACEWAYS
Design
Piping Design and Plant Layout Engineering @
more...
